Aspirateur vertical Navigator™ Swivel Pro Complete du Shark®
Description du produit
Ampères | 5.8 amps |
Largeur de la voie de nettoyage | 30.48 cm |
Capacité du récipient à poussière | 0.78 L |
Couleur | Peony Red |
Longueur du cordon | 7.62 m |
Longueur du tuyau | 3.35 m |
Dimensions du produit | 24.51 cm L x 33.02 cm W x 116.0 cm H |
Puissance | 700 watts |
Garantie (ans) | 5 |
voltage | 120 volts |
weight | 6.05 kg |
Livraison standard gratuite pour toute commande supérieure à 75 $*
SharkNinja offre une garantie de remboursement de 60 jours pour les achats effectués sur ce site, ou pour certains produits, une garantie de remboursement de 90 jours. La garantie de remboursement applicable sera indiquée avec votre commande.
Livraison gratuite sur les cartouches de CO2 et les boîtes de recharge. Livraison gratuite sur les gouttes d'eau aromatisées Ninja Thirsti™ pour un total de 45 $ ou plus. Les commandes sont généralement expédiées dans un délai de 4 à 6 jours ouvrables.
*Ne s'applique pas à l'extérieur du Canada. Les commandes à expédier aux Territoires du Nord-Ouest, au Yukon ou au Nunavut ou à d'autres territoires hors du Canada ou à une adresse internationale sont soumises à un supplément.
Livraison accélérée
Les commandes éligibles sont soumises à des frais d'expédition de 29,99 $. Les commandes passées avant 14 heures (heure de l'Est) seront traitées le même jour ouvrable. Les commandes passées après cette heure seront traitées le jour ouvrable suivant. Les produits achetés avec Affirm ne sont pas éligibles à cette offre. Les produits en pré-commande ou en rupture de stock seront expédiés dès que les stocks seront disponibles. Les commandes sont généralement expédiées dans un délai de 1 à 2 jours ouvrables.
- Suceur plat
- Outil à meubles
- Brosse à épousseter
How do I assemble my vacuum?
- Insert the wand into the floor nozzle.
- Insert the handle into the wand.
- Place the pod onto the wand and slide down to connect.
- Connect the hose into the back of the pod, until it clicks into place
For proper operation, ensure all parts are firmly clicked into place.
How do I clean above floors with or without accessories?
- Press the release button on the back of the handle and gently lift it off the wand. Add an accessory and begin cleaning.
To remove the handle and wand together:
- With the handle still attached to the wand, remove the cord from the clip.
- Press the wand release button and gently pull up on the handle to remove the wand from the pod.
- Add an accessory to the end of the wand and begin cleaning.
- To replace, insert the wand into the pod and press down until it clicks into place.
How do I use the different cleaning modes?
For bare floors and delicate area rugs:
- Slide the selector switch to setting I, Hard Floor.
- To activate the brushroll, gently step on the floor nozzle and tilt the handle back.
- Note that the brushroll will spin slower in Hard Floor mode.
For carpets:
- Slide the selector switch to setting II, Carpet.
- To activate the brushroll, gently step on the floor nozzle and tilt the handle back.
- The brushroll will spin faster in Carpet mode.
When and how do I clean the filters?
Rinse the pre-motor foam and felt filters every month, or as needed.
- Make sure the vacuum is unplugged.
- Remove the dust cup and pull the foam and felt filters out from the pod.
- Rinse filters thoroughly in cold water until the water runs clear. DO NOT place filters in the dishwasher or washing machine.
- Squeeze out excess water and let filters air-dry completely for at least 24 hours before replacing.
- When filters are completely dry, reinstall the felt filter first, then add the foam filter on top.
Rinse the post-motor HEPA filter every 12 months, or as needed.
- Make sure the vacuum is unplugged.
- Remove the dust cup by pressing the button on the dust cup handle.
- Press down on the top of the filter door, then tilt the door and lift it out.
- Remove the HEPA filter cartridge and rinse under cold water, dirty side down, until the water runs clear.
- Allow the filter to air-dry completely for 24 hours.
- Once the HEPA filter is dry, reinstall it. Insert the bottom into the pod first, then press in the top until it clicks into place.
- To reinstall the filter door, insert the bottom into the pod first, then press in the top until it clicks into place.
When and how do I empty the dust cup?
- Press the release button on the top of the dust cup handle.
- Tilt the dust cup and lift it away from the vacuum body.
- Hold the dust cup over the trash and press the bottom door release button on the front of the dust cup. The bottom lid will drop open.
- Tap gently to empty contents.
- Close the lid, pressing it until it clicks into place.
- If needed, turn the dust cup upside down over the trash and press the top door release button.
- Tap gently to remove contents and wipe the interior of the dust cup clean with a soft cloth.
- To reinsert the dust cup, install the bottom into the pod first, then press in the top until it clicks into place.